Kia Forte: Specifications - Engine Control / Fuel System - Kia Forte TD 2014-2018 Service ManualKia Forte: Specifications

Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Engine Control / Fuel System / Specifications

Fuel Delivery System
Items
Specification
Fuel Tank
Capacity
50 lit. (13.2 U.S.gal., 52.8 U.S.qt., 44.0 Imp.qt.)
Fuel Filter
Type
Paper type
Fuel Pressure Regulator
Regulated Fuel Pressure
323 ~ 363 kPa (3.3 ~ 3.7 kgf/cm², 46.9 ~ 52.6 psi)
Fuel Pump
Type
Electrical, in-tank type
Driven by
Electric motor

Sensors
Manifold Absolute Pressure Sensor (MAPS)
▷ Type: Piezo-resistive pressure sensor type
▷ Specification
Pressure [kPa (kgf/cm², psi)]
Output Voltage (V)
20.0 (0.20, 2.9)
0.79
46.7 (0.47, 6.77)
1.84
101.3 (1.03, 14.7)
4.0

Intake Air Temperature Sensor (IATS)
▷ Type: Thermistor type
▷ Specification
Temperature [°C(°F)]
Resistance (kΩ)
-40(-40)
40.93 ~ 48.35
-20(-4)
13.89 ~ 16.03
0(32)
5.38 ~ 6.09
10(50)
3.48 ~ 3.90
20(68)
2.31 ~ 2.57
40(104)
1.08 ~ 1.21
50(122)
0.76 ~ 0.85
60(140)
0.54 ~ 0.62
80(176)
0.29 ~ 0.34

Engine Coolant Temperature Sensor (ECTS)
▷ Type: Thermistor type
▷ Specification
Temperature [°C(°F)]
Resistance (kΩ)
-40(-40)
48.14
-20(-4)
14.13 ~ 16.83
0(32)
5.79
20(68)
2.31 ~ 2.59
40(104)
1.15
60(140)
0.59
80(176)
0.32

Throttle Position Sensor (TPS) [ integrated into ETC module]
▷ Type : Hall IC Non-contact sensor type
▷ Specification
Throttle angle (°)
Output voltage (V) [Vref = 5.0V]
TPS1
TPS2
0
0.5
4.5
10
0.96
4.05
20
1.41
3.59
30
1.87
3.14
40
2.32
2.68
50
2.78
2.23
60
3.23
1.77
70
3.69
1.32
80
4.14
0.86
90
4.6
0.41
98
4.65
0.35
C.T (0)
0.5
4.5
W.O.T (86)
4.41
0.59

Crankshaft Position Sensor (CKPS)
▷ Type: Magnetic field sensitive Type
Item
Specification
Coil Resistance (Ω)
774 ~ 946 [20°C (68°F)]

Camshaft Position Sensor (CMPS)
▷ Type: Hall effect type
Knock Sensor (KS)
▷ Type: Piezo-electricity type
▷ Specification
Item
Specification
Capacitance (pF)
850 ~ 1,150

Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 1]
▷ Type: Zirconia (ZrO2) [Linear] type
▷ Specification
Item
Specification
Heater Resistance (Ω)
2.4 ~ 4.0 [20°C(69.8°F)]

Heated Oxygen Sensor (HO2S) [Bank 1/Sensor 2]
▷ Type: Zirconia (ZrO2) [Binary] type
▷ Specification
A/F Ratio (λ)
Output Voltage(V)
RICH
0.6 ~ 1.0
LEAN
0 ~ 0.4

Item
Specification
Heater Resistance (Ω)
Approx. 9.0 [20°C(68°F)]

Accelerator Position Sensor (APS)
▷ Type: Variable resistor type
▷ Specification
Accelerator
Position
Output Voltage (V)
APS1
APS2
C.T
0.7 ~ 0.8
0.29 ~ 0.46
W.O.T
3.85 ~ 4.35
1.93 ~ 2.18

Fuel Tank Pressure Sensor (FTPS)
▷ Type: Piezo - Resistivity type
▷ Specification
Pressure [kPa (kgf/cm², in H2O)
Output Voltage (V)
-6.67 (-0.068, -26.8)
0.5
0
2.5
+6.67 (0.068, 26.8)
4.5

Actuators
Injector
▷ Specification
Item
Specification
Coil Resistance (Ω)
13.8 ~ 15.2 [20°C(68°F)]

ETC Motor [integrated into ETC Module]
▷ Specification
Item
Specification
Coil Resistance (Ω)
0.3 ~ 100 [20°C(68°F)]

Purge Control Solenoid Valve (PCSV)
▷ Specification
Item
Specification
Coil Resistance (Ω)
22.0 ~ 26.0 [20°C(68°F)]

CVVT Oil Control Valve (OCV)
▷ Specification
Item
Specification
Coil Resistance (Ω)
9.4~10.4 [20°C(68°F)]

Variable Intake Solenoid (VIS) Valve
▷ Specification
Item
Specification
Coil Resistance (Ω)
30.0 ~ 35.0 [20°C(68°F)]

Variable Charge Motion Actuator (VCMA)
▷ Specification
[Motor]
Item
Specification
Coil Resistance (Ω)
3.4 ~ 4.4 [20°C(68°F)]

[Position Sensor]
Item
Specification
Coil Resistance (kΩ)
3.44 ~ 5.16 [20°C(68°F)]

Ignition Coil
▷ Type: Stick type
▷ Specification
Item
Specification
Primary Coil Resistance (Ω)
0.75 ± 15% [20°C(68°F)]
Secondary Coil Resistance (kΩ)
5.9 ± 15% [20°C(68°F)]

Canister Close Valve (CCV)
▷ Specification
Item
Specification
Coil Resistance (Ω)
19.5 ~ 22.5 [20°C(68°F)]

Engine Control / Fuel System
...

Service Standard
Item Specification Ignition Timing (°) BTDC 5 ± 10 Idle Speed (rpm) A/C OFF Neutral, N, P-range 640 ± 100 D-range ...

See also:

Smart Key Diagnostic Inspection
Self Diagnosis With GDS Smart key system defects can be quickly diagnosed with the GDS. GDS operates actuator quickly to monitor, input/output value and self diagnosis. The following thr ...

Injector Description
Based on information from various sensors, the ECM can calculate the fuel amount to be injected. The fuel injector is a solenoid-operated valve and the fuel injection amount is controlled by ...

Power Window Relay Inspection
Diagnosis With GDS 1. It will be able to diagnose defects of power window with GDS quickly. GDS can operates actuator forcefully, input/output value monitoring and ...

Copyright © www.kifomanual.com 2014-2024