Kia Forte: Specification
Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Driveshaft and axle / Specification
| Engine |
T/M |
Joint type |
Max . permissible angle |
||
| Outer |
Inner |
Outer |
Inner |
||
| Nu 1.8 MPI |
6 M/T |
BJ#22 |
TJi#22 |
46.5° |
23° |
| Nu 1.8 MPI |
6 A/T |
BJ#24 |
TJi#22 |
46.5° |
23° |
| Nu 2.0GDI |
6 M/T |
BJ#23 |
TJi#23 |
46.5° |
23° |
| Nu 2.0GDI |
6 A/T |
BJ#24 |
TJi#22 |
46.5° |
23° |
| Gamma 1.6 T-GDI |
6 M/T |
BJ#23 |
TJi#23 |
46.5° |
23° |
| Gamma 1.6 T-GDI |
6 A/T |
BJ#24 |
TJ#22 |
46.5° |
23° |
| Tightening torque |
| Item |
N.m |
kgf.m |
Ib.ft |
|
| Front |
Tire wheel hub nuts |
88.3 ~ 107.9 |
9.0 ~ 11.0 |
65.1 ~ 79.6 |
| Drive shaft coking nut |
240.3 ~ 269.7 |
24.5 ~ 27.5 |
177.2 ~ 198.9 |
|
| Strut assembly to knuckle |
137.3 ~ 156.9 |
14.0 ~ 16.0 |
101.3 ~ 115.7 |
|
| Brake caliper mounting bolt |
78.4 ~ 98.0 |
8.0 ~ 10.0 |
57.8 ~ 72.3 |
|
| Wheel speed sensor mounting bolt |
6.8 ~ 10.7 |
0.7 ~ 1.1 |
5.0 ~ 7.9 |
|
| Brake disc mounting bolt |
4.9 ~ 5.8 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
| Lower arm to knuckle |
78.5 ~ 88.3 |
8.0 ~ 9.0 |
57.9 ~ 65.1 |
|
| Tie rod end ball joint nut |
23.5 ~ 33.3 |
2.4 ~ 3.4 |
19.4 ~ 24.5 |
|
| Rear |
Tire wheel hub nuts |
88.2 ~ 107.8 |
9.0 ~ 11.0 |
65.0 ~ 79.5 |
| Rear caliper to torsion beam axle |
63.7 ~ 73.5 |
6.5 ~ 7.5 |
47.0 ~ 54.2 |
|
| Rear herb assembly to torsion beam axle |
49.0 ~ 58.8 |
5.0 ~ 6.0 |
36.1 ~ 43.3 |
|
| Disc fixing screw |
4.9 ~ 5.9 |
0.5 ~ 0.6 |
3.6 ~ 4.3 |
|
| Wheel speed sensor mounting bolt |
6.9 ~ 10.8 |
0.7 ~ 1.1 |
5.1 ~ 8.0 |
|
Lubricants
Engine
TM
Joint
Lubricants
Quantity
Nu 1.8 MPI
6 M/T
BJ
RBA
90g
TJ
CW09-VX21
135g
Nu ...
See also:
Description
Component location : Manual transaxle
case
Operation principle : Back up lamp
switch is pushed by the reverse lug sliding when select arm, and switches the
back up lamp.
Funct ...
Drive plate Removal and Installation
1.
Remove the automatic transaxle.
(Refer to Automatic Transaxle System - "Automatic Transaxle")
2.
Remove the drive plate (A ...
A/C Pressure Transducer Inspection
1.
Measure the pressure of high pressure line by measuring voltage
output between NO.1 and NO.2 terminals.
2.
Inspect the voltage v ...
Copyright © www.kifomanual.com 2014-2024