Kia Optima Manuals

Kia Forte: Rear Seat Back Cover Replacement - Rear Seat - Body (Interior and Exterior) - Kia Forte TD 2014-2018 Service ManualKia Forte: Rear Seat Back Cover Replacement

Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Body (Interior and Exterior) / Rear Seat / Rear Seat Back Cover Replacement

(4Door, 2Door)
[LH]
  
•
Put on gloves to protect your hands.
  
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the rear seat back assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Push the lock pin (B), remove the rear seat headrest (A).
3.
After loosening the mounting screws, then remove the rear seat back webbing guide (A).
4.
After loosening the mounting screws, then remove the rear seat back latch cover (A).
5.
Remove the protector (A) located in the bottom side of the rear seat back.
6.
Zip off the rear seat back cover located in the side (A), and then pull it up.
7.
Turn the rear seat back cover inside out. Then pull out the headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.
8.
Remove the rear seat back cover (A) from the rear seat back frame (B).
9.
After removing the hog-ring clips (A) on the rear of seat back and remove the rear seat back cover (B).
10.
Install in the reverse order of removal.
  
•
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
•
Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

[RH]
  
•
Put on gloves to protect your hands.
  
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the rear seat back assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Push the lock pin (B), remove the rear seat headrest (A).
3.
After loosening the mounting screws, then remove the rear seat back webbing guide (A).
4.
After loosening the mounting screws, then remove the rear seat back latch cover (A).
5.
Remove the rear back armrest cap (A).
6.
After loosening the mounting bolt, then remove the rear back armerst (B).
7.
After loosening the mounting screws, then remove the rear back armerst panel (A).
8.
Remove the protector (A) located in the bottom side of the rear seat back.
9.
Zip off the rear seat back cover located in the side (A), and then pull it up.
10.
Turn the rear seat back cover inside out. Then pull out the headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.
11.
Remove the rear seat back cover (A) from the rear seat back frame (B).
12.
After removing the hog-ring clips (A) on the rear of seat back and remove the rear seat back cover (B).
13.
Install in the reverse order of removal.
  
•
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
•
Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

(5Door)
[LH]
  
•
Put on gloves to protect your hands.
  
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the rear seat back assembly [LH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Push the lock pin (B), remove the rear seat headrest (A).
3.
Using a screwdriver or remover, remove the rear seat back upper bezel (A).
4.
After loosening the mounting screw, then remove the rear seat back latch cover (A).
5.
Disconnect the rear seat back cover hooks (A).
6.
Remove the rear seat back panel (A).
7.
Turn the rear seat back cover inside out. Then pull out the headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.
8.
Remove the rear seat back cover (A) from the rear seat back frame (B).
9.
After removing the hog-ring clips (A) on the rear of seat back and remove the rear seat back cover (B).
10.
Install in the reverse order of removal.
  
•
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
•
Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

[RH]
  
•
Put on gloves to protect your hands.
  
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the rear seat back assembly [RH].
(Refer to Rear Seat - "Rear Seat Assembly")
2.
Push the lock pin (B), remove the rear seat headrest (A).
3.
Using a screwdriver or remover, remove the rear seat back upper bezel (A).
4.
Using a flat-tip screwdriver, push the locking pin (B) and then remove the rear center seat belt upper anchor cover (A).
5.
After loosening the mounting screw, then remove the rear seat back latch cover (A).
6.
Remove the rear back armrest cap (A).
7.
After loosening the mounting bolt, then remove the rear back armerst (B).
8.
After loosening the mounting screws, then remove the rear back armerst panel (A).
9.
Disconnect the rear seat back cover hooks (A).
10.
Remove the rear seat back panel (A).
11.
Turn the rear seat back cover inside out. Then pull out the headrest guides (A) while pinching both sides of the lower part of the guides, and remove them.
12.
Remove the rear seat back cover (A) from the rear seat back frame (B).
13.
After removing the hog-ring clips (A) on the rear of seat back and remove the rear seat back cover (B).
14.
Install in the reverse order of removal.
  
•
To prevent wrinkles, make sure the material is stretched evenly over the cover (B) before securing the hog-ring clips (A).
•
Replace the hog-ring clips with new ones using special tool (C) (09880-4F000).

Rear Seat Back Cover Component Location
(4Door, 2Door) 1. Rear seat back cover [LH] 2. Rear seat back cover [RH] (5Door) 1. Rear seat back assembly [LH] 2. Rear seat ...

Rear Seat Cushion Cover Component Location
1. Rear seat cushion cover ...

See also:

Seat Heater (Non-Air Ventilation) Component Location
...

Removal
1. Disconnect the negative (-) battery terminal. 2. Remove the crash pad lower panel. (Refer to Body - "Crash Pad Low Panal") ...

Special Service Tools
Tool Name / Number Illustration Description Strut spring compressor 09546-26000 Compression of coli spring ...

Categories

Copyright www.kifomanual.com 2014-2026