Kia Forte: 2. TCM Terminal Function
Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Automatic Transaxle System / Automatic Transaxle Control System / 2. TCM Terminal Function
Connector [A]
| Pin |
Description |
Pin |
Description |
| 1 |
- |
54 |
- |
| 2 |
Line pressure control solenoid valve (LINE_VFS) |
55 |
- |
| 3 |
Torque converter control solenoid valve (T/CON_VFS) |
56 |
- |
| 4 |
35R clutch control solenoid valve (35R/C_VFS) |
57 |
- |
| 5 |
- |
58 |
- |
| 6 |
- |
59 |
- |
| 7 |
Inhibitor switch signal "S1" |
60 |
- |
| 8 |
Inhibitor switch signal "S2" |
61 |
- |
| 9 |
Inhibitor switch signal "S3" |
62 |
- |
| 10 |
Inhibitor switch signal "S4" |
63 |
- |
| 11 |
- |
64 |
- |
| 12 |
- |
65 |
ON/OFF solenoid valve B(SS-B) |
| 13 |
- |
66 |
ON/OFF solenoid valve A(SS-A) |
| 14 |
- |
67 |
Battery (B+) |
| 15 |
- |
68 |
- |
| 16 |
- |
69 |
Oil temperature sensor (+) |
| 17 |
- |
70 |
- |
| 18 |
- |
71 |
- |
| 19 |
- |
72 |
- |
| 20 |
- |
73 |
Output speed sensor signal |
| 21 |
- |
74 |
- |
| 22 |
- |
75 |
- |
| 23 |
Underdrive brake control solenoid valve (UD/B_VFS) |
76 |
- |
| 24 |
26 brake control solenoid valve (26/B_VFS) |
77 |
- |
| 25 |
Overdrive clutch control solenoid valve (OD/C_VFS) |
78 |
- |
| 26 |
- |
79 |
- |
| 27 |
- |
80 |
- |
| 28 |
- |
81 |
- |
| 29 |
- |
82 |
- |
| 30 |
- |
83 |
- |
| 31 |
- |
84 |
- |
| 32 |
- |
85 |
- |
| 33 |
- |
86 |
Solenoid supply power 1 |
| 34 |
- |
87 |
Solenoid supply power 2 |
| 35 |
- |
88 |
Battery (B+) |
| 36 |
- |
89 |
- |
| 37 |
- |
90 |
Output speed sensor power |
| 38 |
- |
91 |
Input speed sensor power |
| 39 |
- |
92 |
- |
| 40 |
- |
93 |
- |
| 41 |
- |
94 |
Input speed sensor signal |
| 42 |
- |
95 |
- |
| 43 |
- |
96 |
- |
| 44 |
Ground (Power 1) |
97 |
- |
| 45 |
Ground (Power 2) |
98 |
- |
| 46 |
Shift lock solenoid |
99 |
- |
| 47 |
- |
100 |
- |
| 48 |
Oil temperature sensor (-) |
101 |
- |
| 49 |
- |
102 |
- |
| 50 |
- |
103 |
- |
| 51 |
- |
104 |
- |
| 52 |
- |
105 |
- |
| 53 |
- |
|
TCM Terminal Input/ Output Signal
Connector [A]
Pin
Description
Condition
Input/output value
Type
Level
1
-
...
See also:
Removal
1.
Disconnect the negative (-) battery terminal.
2.
Remove the steering wheel.
(Refer to Steering System - "Steering Wheel")
...
Cylinder Block Inspection
1.
Remove gasket material.
Using a gasket scraper, remove all the gasket material from the
top surface of the cylinder block.
2.
Cl ...
Dynamic Damper Installation
1.
Apply soap powder on the shaft to prevent being damaged between
the shaft spline and the dynamic damper.
2.
Install the dynamic damper.
...
Copyright © www.kifomanual.com 2014-2025