Kia Forte: Cooling Fan Description
Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Engine Mechanical System / Cooling System / Cooling Fan Description
[Air conditioning type]
The cooling fan operates in 2 stages (HIGH/LOW). The engine control module
(ECM) controls the cooling fan according to the coolant temperature, vehicle
speed and A/C operation.
[Cooling fan operation conditions]
| A/C switch |
A/C pressure [kgf/cm² G (psi G)] |
Vehicle speed [km/h (mph)] |
Coolant temperature [°C (°F)] |
Cooling fan speed |
| OFF |
ㅡ |
V < 45 (28) |
100 ~ 105 (212 ~ 221) |
LOW |
| 105 (221) or above |
HIGH |
|||
| 45 (28) ≤ V < 80 (49.7) |
100 ~ 105 (212 ~ 221) |
LOW |
||
| 105 (221) or above |
HIGH |
|||
| 80 (49.7) ≤ V |
105 (221) or above |
HIGH |
||
| ON |
P < 6 (85.3) |
All |
105 (221) or above |
HIGH |
| 6 (85.3) ≤ P < 12 (170.7) |
V < 45 (28) |
60 ~ 100 (140 ~ 212) |
LOW |
|
| 100 (212) or above |
HIGH |
|||
| 45 (28) ≤ V < 80 (49.7) |
95 ~ 100 (203 ~ 212) |
LOW |
||
| 100 (212) or above |
HIGH |
|||
| 80 (49.7) ≤ V |
105 (221) or above |
HIGH |
||
| 12 (170.7) ≤ P < 15.5 (120.5) |
V < 45 (28) |
-30 ~ 95 (-22 ~ 203) |
LOW |
|
| 95 (203) or above |
HIGH |
|||
| 45 (28) ≤ V < 80 (49.7) |
95 ~ 100 (203 ~ 212) |
LOW |
||
| 100 (212) or above |
HIGH |
|||
| 80 (49.7) ≤ V |
105 (221) or above |
HIGH |
||
| 15.5 (120.5) ≤ P |
All |
-30 (-22) or above |
HIGH |
[Non-Air conditioning type]
The cooling fan operates in 1 stages (HIGH). The engine control module
(ECM) controls the cooling fan according to the coolant temperature, vehicle
speed and A/C operation.
[Cooling fan operation conditions]
| A/C switch |
A/C pressure [kgf/cm² G (psi G)] |
Vehicle speed [km/h (mph)] |
Coolant temperature [°C (°F)] |
Cooling fan speed |
| OFF |
ㅡ |
V < 45 (28) |
100 ~ 105 (212 ~ 221) or above |
HIGH |
| 45 (28) ≤ V < 80 (49.7) |
100 ~ 105 (212 ~ 221) or above |
HIGH |
||
| 80 (49.7) ≤ V |
105 (221) or above |
HIGH |
Cooling Fan Components
1. Cooling fan
2. Fan motor
3. Cooling fan shroud
4. Resister
...
Cooling Fan Specifications
Item
Specification
Fan type
PULLER
Fan speed control
Resistor (HI-LOW-OFF)
Air flow rate [㎥/h (yd³/h)]
1,700 (2,22 ...
See also:
General Inspection
After or before servicing the EPS system, perform the troubleshooting
and test procedure as follows. Compare the system condition with normal condition
in the table below and if abnormal symp ...
Hands Free Mic Inspection
1.
Disconnect the negative(-) battery terminal.
2.
Remove the handsfree mic (A) after disconnect the connector from
roof trim.
...
Dynamic Damper Installation
1.
Apply soap powder on the shaft to prevent being damaged between
the shaft spline and the dynamic damper.
2.
Install the dynamic damper.
...
Copyright © www.kifomanual.com 2014-2025