Kia Forte: Roof Trim Assembly Replacement

Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Body (Interior and Exterior) / Roof Trim / Roof Trim Assembly Replacement

•	Put on gloves to protect your hands.

•	When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.

•	Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.

•	Take care not to bend or scratch the trim and panels.

1.	Remove the rear seat cushion assembly. (Refer to Rear Seat - "Rear Seat Assembly")

2.	Remove the rear seat back assembly. (Refer to Rear Seat - "Rear Seat Assembly")

3.	Remove the front pillar trim. (Refer to Interior Trim - "Front Pillar Trim")

4.	Remove the canter pillar upper trim. (Refer to Interior Trim - "Center Pillar Trim")

5.	Remove the rear package tray trim. (4Door, 2Door) (Refer to Interior Trim - "Rear Package Tray Trim")

6.	Remove the sunvisor and retainer. (Refer to Roof Trim - "Sunvisor")

7.	Remove the assist handle. (Refer to Roof Trim - "Assist Handle")

8.	Remove the garment hook. (2Door) (Refer to Roof Trim - "Garment Hook")

9.	Remove the overhead console lamp. (Refer to Body Electrical System - "Overhead Console Lamp")

10.	Remove the room lamp. (Refer to Body Electrical System - "Room Lamp")

11.	Remove the rear window glass. (Refer to "Rear Window Glass")

12.	Tilt the front seat back towards the rear of the vehicle as far as possible.

13.	Remove the ECM mirror cover (A).

14.	Disconnect the ECM mirror connector (B).

15.	Remove the auto defog sensor cover (A).

16.	Disconnect the auto defog sensor connector (B).

17.	Disconnect the roof trim main connector (A) and the mounting clips (B) in the front pillar. [Driver's]

18.	Using a clip remover, detach the roof trim assembly mounting clips.

19.

Pull back the roof trim assembly (A) through the place where the rear window glass was removed.

•	Take care not to damage the roof trim when removing.

20.	Remove the vanity lamp. (Refer to Body Electrical System - "Vanity Lamp")

21.	Remove the hands free mic. (Refer to Body Electrical System - "Hands Free Mic")

22.

Remove roof trim wiring harness (A) from the roof trim (B).

•	Take care not to damage the roof trim wiring harness (A) when removing.

1.	Apply the hot melt continuously when installing the roof trim wiring harness (A) on the roof trim (B) using the hot melt gun tool.

2.	Put anti-noise pad (C) on roof trim (B) to prevent the noise.

23.

Install in the reverse order of removal.

•	Make sure the connector is plugged in properly.

•	Replace any damaged clips.

Roof Trim Assembly Component Location

1. Roof Trim Assembly ...

Interior Trim

...

See also:

Torque Converter Control Solenoid Valve (T/CON_VFS) Specifications
Direct control VFS[T/CON] ▷ Control type : Normal low type Control Pressure kpa (kgf/cm², psi) 9.81 ~ 500.14 (0.1 ~ 5.1,1.42 ~ 72.54) Current value(mA) ...

Transaxle Oil Temperature Sensor Specifications
▷ Type: Negative Thermal Coefficient(NTC) Type Temp.[(°C)°F] Resistance (kΩ) (-40)-40 48.1 (-20)-4.0 15.6 (0)32.0 ...

Basic method of USE :
Audio CD / MP3 CD / USB / iPod® / My Music Press the key to change the mod mode in order of CD ➟ USB(iPod®) ➟ AUX ➟ My Music ➟ BT Audio. The folder/file name is displa ...

Categories

Copyright © www.kifomanual.com 2014-2025