Kia Forte: Components - IMS (Integrated Memory) - Body Electrical System - Kia Forte TD 2014-2018 Service ManualKia Forte: Components

Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Body Electrical System / IMS (Integrated Memory) / Components

Input/Output Specification

IMS input/output pin information
No.
Signal Name
I/O
Contents
Remark
A1
-
-
-
 
A2
FRT height motor up
O
Front height motor up output
 
A3
RR height motor up
O
Rear height motor up output
 
A4
Recline motor FWD
O
Recline motor Forward output
 
A5
Slide motor FWD
O
Slide motor Forward output
 
A6
-
-
-
 
A7
FRT height motor down
O
Front height motor down output
 
A8
-
-
-
 
A9
-
-
-
 
A10
RR height motor down
O
Rear height motor down output
 
A11
Recline motor BWD
O
Recline motor backward output
 
A12
Slide motor BWD
O
Slide motor backward output
 
B1
B+(Power)
I
Power B+ for operating motor
 
B2
GND (Power)
I
Power GND for operating motor
 
B3
B+(Power)
I
Power B+ for operating motor
 
B4
-
-
-
 
B5
GND (Power)
I
Power GND for operating motor
 
C1
-
-
-
 
C2
-
-
-
 
C3
Slide FWD manual switch
I
Slide forward manual switch input
On : GND
C4
Recline FWD manual switch
I
Recline forward manual switch input
On : GND
C5
FRT height up manual switch
I
Front height up manual switch input
On : GND
C6
RR height up manual switch
I
Rear height up manual switch input
On : GND
C7
Slide motor sensor
I
Slide motor sensor input
Pulse signal
C8
Recline motor sensor
I
Recline motor sensor input
Pulse signal
C9
FRT height motor sensor
I
Front height motor sensor input
Pulse signal
C10
Sensor Vcc(Seat)
O
VCC for operating sensor
5V
C11
-
-
-
 
C12
-
-
-
 
C13
Slide RR manual switch
I
Slide rear manual switch input
ON : GND
C14
Recline RR manual switch
I
Recline rear manual switch input
ON : GND
C15
FRT height down manual switch
I
Front height down manual switch input
ON : GND
C16
RR height down manual switch
-
Rear height down manual switch input
ON : GND
C17
-
-
-
 
C18
-
-
-
 
C19
-
-
-
 
C20
-
-
-
 
D1
SET switch
I
SET switch input
ON : GND
D2
RR height up sensor
I
Rear height up motor sensor
Pulse signal
D3
SW1 switch
I
SW1 switch input
ON : GND
D4
CAN high
I/O
CAN high BUS
 
D5
CAN low
I/O
CAN low BUS
 
D6
SW2 switch
I
SW2 switch input
ON : GND
D7
IGN1
I
IGN1 input
BAT
D8
B+(ECU)
I
ECU power input
BAT
D9
GND(SIGNAL)
I
Sinal ground
 
D10
-
-
-
 
D11
-
-
-
 
D12
-
-
-
 
D13
-
-
-
 
D14
-
-
-
 
D15
-
-
-
 
D16
-
-
-
 

Operation
Control Specification 1. MANUAL Operation (1) MANUAL Seat Operation SEAT is to be operated by MANUAL switch Input of SEAT. SLI ...

Circuit Diagram
...

See also:

Cylinder Head Removal
Engine removal is not required for this procedure.    • Use fender covers to avoid damaging pa ...

Seat Heater Inspection
Front Seat 1. Check for continuity and measure the resistance between terminals. No. Description No. Descripti ...

Intake Air Temperature Sensor (IATS) Circuit Diagram
(M/T) (A/T) ...

Copyright © www.kifomanual.com 2014-2024