Kia Forte: Removal

Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Automatic Transaxle System / Automatic Transaxle / Removal

1.	Engine cover. (Refer to Engine Mechanical System - "Engine cover")

2.	Air cleaner assembly and air duct. (Refer to Engine Mechanical System - "Air cleaner")

3.	Battery and battery tray. (Refer to Engine Electrical System - "Battery")

4.	Remove the ECM (Engine Control Module). (Refer to Fuel System - "Engine Control Module (ECM)")

5.	Remove the ground line after removing the bolt (A).

6.	Dissconnect the solenoid valve connector (A) and inhibitor switch connector (B).

7.

Remove the control cable (C) after removing the nut (A) and the bolt (B).

Tightening torque:

(A) 9.8 ~ 13.7 N.m (1.0 ~ 1.4 kgf.m, 7.2 ~ 10.1 lb-ft)

(B) 14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)

8.	Disconnect the hose (B) after removing the automatic transaxle fluid cooler hose clamp (A).

9.

Remove the wiring mounting bolt (A).

Tightening torque:

9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

10.

Remove the solenoid valve connector and inhibitor switch connector wiring mounting bracket (A)and(B).

Tightening torque:

Bolt (A) :

9.8 ~ 11.8 N.m (1.0 ~ 1.2 kgf.m, 7.2 ~ 8.7 lb-ft)

Bolt (B) :

14.7 ~ 21.6 N.m (1.5 ~ 2.2 kgf.m, 10.9 ~ 15.9 lb-ft)

11.	Remove the cowl top cover.(Refer to Body - "Cowl Top Cover")

12.	Assemble the engine support fixture.(Refer to Special Service Tools-"Engine support fixture assembly drawing")

13.	Using the engine support fixture (beam No.: 09200-38001 or 09200-3N000, supporter No.: 09200-2S000, adapter No.: 09200-4X000), hold the engine and transaxle assembly safely.

14.

Remove the automatic transaxle upper mounting bolt (A-2ea) and the starter motor mounting bolt (B-2ea).

Tightening torque:

(A,B) 42.2 ~ 54.0 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

15.	Remove the automatic transaxle mounting bracket cover (A).

16.

Remove the automatic transaxle mounting bracket bolts (A).

Tightening torque:

88.3 ~ 107.9 N.m (9.0 ~ 11.0 kgf.m, 65.1 ~ 79.8 lb-ft)

17.

Remove the automatic transaxle mounting support bracket (A).

Tightening torque:

58.8 ~ 78.5 N.m (6.0 ~ 8.0 kgf.m, 43.4 ~ 57.9 lb-ft)

18.	Lift the vehicle with a jack.

19.

Remove the under cover (A).

Tightening torque:

6.9 ~ 10.8 N.m (0.7 ~ 1.1 kgf.m, 5.1 ~ 8.0 lb-ft)

20.

Remove the roll stopper (A).

Tightening torque

Nut (B):

107.9 ~ 127.5 N.m (11.0 ~ 13.0 kgf.m, 79.6 ~ 94.0 lb-ft)

Bolt (C):

49.0 ~ 63.7 N.m (5.0 ~ 6.5 kgf.m, 36.2 ~ 47.0 lb-ft)

21.	Remove the drive shaft assembly. (Refer to Driveshaft and Axle - "Front Driveshaft")

22.

Remove the air guide bracket(A).

Tightening torque:

8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)

23.

Remove the dust cover (A).

Tightening torque :

42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)

24.

Remove the torque converter mounting bolts(A) with rotating the crankshaft.

Tightening torque:

45.1 ~ 52.0 N.m (4.6 ~ 5.3 kgf.m, 33.3 ~ 38.3 lb-ft)

25.

Remove the automatic transaxle with a jack after removing the mounting bolt (A-1ea, B-3ea).

Tightening torque:

(A) 42.2 ~ 53.9 N.m (4.3 ~ 5.5 kgf.m, 31.1 ~ 39.8 lb-ft)

(B) 42.2 ~ 48.1 N.m (4.3 ~ 4.9 kgf.m, 31.1 ~ 35.4 lb-ft)

Components Location

1. Converter housing 2. Automatic transaxle upper mounting bolt 3. Shift cable bracket 4. Manual control lever 5. Rear cover 6. Oil cooler tube 7. Oil level plug 8. Val ...

Installation

1. Install in the reverse order of removal. If the oil seal on the transaxle case side is da ...

See also:

Intake Actuator Description
The intake actuator is located at the blower unit. It regulates the intake door by the signal from the control unit. Pressing the intake selection switch will shift between recirculation and ...

26 Brake Control Solenoid Valve(26/B_VFS) Description
26 Brake(26/B) Control Solenoid Valve is attached to the valve body. This variable force solenoid valve directly controls the hydraulic pressure inside the 26 Brake. ...

Automatic climate control system
...

Categories

Copyright © www.kifomanual.com 2014-2026