Kia Forte: Inside rearview mirror - Mirrors - Features of your vehicle - Kia Forte TD 2014-2019 Owners ManualKia Forte: Inside rearview mirror

Second generation YD (2014-2019) / Kia Forte TD 2014-2019 Owners Manual / Features of your vehicle / Mirrors / Inside rearview mirror

Adjust the rearview mirror so that the center view through the rear window is seen. Make this adjustment before you start driving.

Do not place objects in the rear seat which would interfere with your vision through the rear window.

WARNING - Mirror adjustment

Do not adjust the rearview mirror while the vehicle is moving. This could result in loss of control.

Day/night rearview mirror (if equipped)

Make this adjustment before you start driving and while the day/night lever is


Make this adjustment before you start driving and while the day/night lever is in the day position.

Pull the day/night lever toward you to reduce the glare from the headlights of the vehicles behind you during night driving.

Remember that you lose some rearview clarity in the night position.

Electric chromic mirror with homelink« system (if equipped)

To operate the electric rearview mirror Press the I button (1) to turn the automatic-


To operate the electric rearview mirror Press the I button (1) to turn the automatic- dimming function on. The mirror indicator light will illuminate.

Press the O button (2) to turn the automatic- dimming function off. The mirror indicator light will turn off.

* HomeLink« is a registered trademark of Johnson Controls, Inc.

HomeLink«* Wireless Control System


HomeLink«* Wireless Control System

Your new mirror comes with an integrated Homelink« Universal Transceiver, which allows you to program the mirror to activate your garage door(s), estate gate, home lighting, etc. The mirror actually learns the codes from your various existing transmitters.

WARNING

Retain the original transmitter for future programming procedures (i.e., new vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink« buttons be erased for security purposes (follow step 1 in the "Programming" portion of this text).

Programming

Your vehicle may require the ignition switch to be turned to the ACC position for programming and/or operation of Homelink«. It is also recommended that a new battery be replaced in the hand-held transmitter of the device being programmed to Homelink« for quicker training and accurate transmission of the radiofrequency.

Follow these steps to train your Homelink« mirror:

When programming the buttons for the first time, press and hold the left and


When programming the buttons for the first time, press and hold the left and center buttons ( , 
, ) simultaneously until the indicator light begins to flash after approximately 20
) simultaneously until the indicator light begins to flash after approximately 20 seconds. (This procedure erases the factory-set default codes. Do not perform this step to program additional hand-held transmitters.)

✽ NOTICE

For non rolling code garage door openers, follow steps 2 - 3. For rolling code garage door openers, follow steps 2 - 6. For Canadian Programming, please follow the Canadian Programming section. For help with determining whether your garage is non-rolling code or rolling code, please refer to the garage door openers ownerĺs manual or contact Homelink« customer service at 1-800-355-3515.

2.Press and hold the button on the Homelink« system you wish to train and the


2.Press and hold the button on the Homelink« system you wish to train and the button on the transmitter while the transmitter is approximately 1 to 3 inches away from the mirror. Do not release the buttons until step 3 has been completed.

3.The Homelink« indicator light will flash, first slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. (The rapid flashing light indicates successful programming of the new frequency signal.)

✽ NOTICE

Some gate operators and garage door openers may require you to replace step #3 with the "cycling" procedure noted in the "Canadian Programming" section of this document.

Mirrors
...

Rolling code programming
To train a garage door opener (or other rolling code equipped devices) with the rolling code feature, follow these instructions after completing the "Programming" portion of this text. (A ...

See also:

Hood Weatherstrip Replacement
1. Remove the hood weatherstrip (A).    Ľ ...

Specifications
Item Specification Master cylinder Type Fixed seal Cylinder I.D. 22.22 mm Piston stroke 45 ▒ 1 mm (1.77 ▒ 0.039 in) ...

Dynamic Damper Components
1. BJ assembly 2. Circlip 3. BJ boot band 4. BJ boot 5. Dynamic damper band 6. Dynamic damper 7. Shaft 8. TJ boot band 9. TJ boot 10. Spider assembly 1 ...

Copyright ę www.kifomanual.com 2014-2019