Kia Optima Manuals

Kia Forte: Rear Package Tray Trim Replacement - Interior Trim - Body (Interior and Exterior) - Kia Forte TD 2014-2018 Service ManualKia Forte: Rear Package Tray Trim Replacement

Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Body (Interior and Exterior) / Interior Trim / Rear Package Tray Trim Replacement

(4Door)
  
•
Put on gloves to protect your hands.
  
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the rear wheel house trim.
(Refer to Interior Trim - "Rear Wheel House Trim")
2.
After loosening the mounting bolt, then remove the rear seat belt lower anchor (A).
[LH,RH]
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)

[Center]
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)

3.
Disconnect the high Mounted stop lamp (A) connecter from inside the trunk.
4.
Remove the rear seat belt upper anchor cover (A).
5.
Using a screwdriver or remover, remove the rear package tray trim (A).
6.
Install in the reverse order of removal.
  
•
Make sure the connector is plugged in properly.
•
Replace any damaged clips.
(2Door)
  
•
Put on gloves to protect your hands.
  
•
When prying with a flat-tip screwdriver, wrap it with protective tape, and apply protective tape around the related parts, to prevent damage.
•
Use a plastic panel removal tool to remove interior trim pieces to protect from marring the surface.
•
Take care not to bend or scratch the trim and panels.
1.
Remove the rear pillar trim.
(Refer to Interior Trim - "Rear Pillar Trim")
2.
After loosening the mounting bolt, then remove the rear seat belt lower anchor (A).
[LH,RH]
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)

[Center]
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)

3.
After loosening the mounting clips and screws, then remove the rear partition trim (A).
4.
Remove the rear seat belt upper anchor cover (A).
5.
Using a screwdriver or remover, remove the rear package tray trim (A).
6.
Install in the reverse order of removal.
  
•
Make sure the connector is plugged in properly.
•
Replace any damaged clips.
Rear Package Tray Trim Component Location
(4Door) 1. Rear package tray trim (2Door) 1. Rear package tray trim ...

Luggage Side Trim Component Location
(5Door) 1. Luggage side trim ...

See also:

Climate control seat (if equipped)
The climate control seat is provided to cool or warm the seat during hot or cold weather by blowing air through small vent holes on the surface of the seat and seatback. While the engine is runn ...

2. TCM Terminal Function
Connector [A] Pin Description Pin Description 1 - 54 - 2 Line pressure control solenoid valve (LINE_VFS) 55 ...

Heater Unit Components
1. Heater Case (Left) 2. Heater Case (Right) 3. Console Separator 4. Defog Door 5. Vent Door 6. Floor Door 7. Mix Door (Manual) 8. Mix Door (DATC-Left) 9. Mix Door ( ...

Categories

Copyright www.kifomanual.com 2014-2026