Kia Forte: Warning Lamp Activation
Second generation YD (2014-2018) / Kia Forte TD 2014-2018 Service Manual / Restraint / Warning Lamp Activation
| Warning Lamp Behavior after Ignition On |
As soon as the operating voltage is applied to the SRSCM ignition input,
the SRSCM activates the warning lamp for a LED lamp check.
The lamp shall turn on for 6 seconds during the initialization phase and
be turned off afterward.
To alert the driver, the warning lamp shall turn on for 6 seconds and
off for one second then on continuously after the operating voltage is applied
if any active fault exists.
| 1. |
Active fault or historical fault counter is greater or equal to
10.
|
| 2. |
Normal or historical fault counter is less than 10.
|
| 3. |
When turning the ignition switch ON during variant coding (EOL)
mode, the airbag warning lamp is turned on and blinks at intervals of
1 second till the coding is completed.
If the variant coding is completed normally, the airbag warning
lamp will turn on for 6 seconds, and then turned off. Otherwise the
airbag warning lamp continuously blinks at intervals of 1 second.
When there is active fault in airbag system or SRSCM internal
fault, the variant coding (EOL) cannot be completed. In this case, perform
the variant coding (EOL) procedure again after troubleshooting with
the GDS.
|
SRSCM Independent Warning Lamp Activation
There are certain fault conditions in which the SRSCM cannot function
and thus cannot control the operation of the standard warning lamp. In these
cases, the standard warning lamp is directly activated by appropriate circuitry
that operates independently of the SRSCM. These cases are:
| 1. |
Loss of battery supply to the SRSCM : warning lamp turned on continuously.
|
| 2. |
Loss of internal operating voltage : warning lamp turned on continuously.
|
| 3. |
Loss of Microprocessor operation : warning lamp turned on continuously.
|
| 4. |
SRSCM not connected : warning lamp turned on continuously.
|
Telltale Lamp Activation
The Telltale Lamp indicates the Passenger Airbag(PAB) enabled and disabled
status based on occupant status of passenger seat. If the passenger seat is
empty or occupied with child (or child seat), the Passenger Airbag is disabled
and the Telltale Lamp is turned ON to inform the driver that the PAB is disabled.
As soon as operating voltage is applied to the SRSCM ignition input, the SRSCM
activates telltale lamp prove out. ODS (Occupant Detection System) will send
an indeterminate status to the SRSCM as a default setting for passenger airbag
deployment during the prove out period.
After ignition on, telltale lamp will turn on for 4 seconds and turn off
for 3 seconds during the initialization phase and be turned ON afterward until
receipt of valid enabled message from ODS system.
Components Location
Supplemental Restraint System Control
Module (SRSCM)
Driver Airbag (DAB) / Passenger Airbag
(PAB)
Side Airbag (SAB)
Curtain Airbag (CA ...
Special Service Tools
Tool(Number and Name)
Illustration
Use
Deployment tool
0957A-34100A
Airbag deployment tool.
Deployment adapter
0957A-3Q100
...
See also:
Heated Oxygen Sensor (HO2S) Removal
[SULEV]
1.
Turn the ignition switch OFF and disconnect the battery negative
(-) cable.
2.
Disconnect the connector (A), and th ...
Instrument Cluster Description
Cluster Variant Coding
As we have more options (ESC, TPMS, etc.) in the car, the dashboard now
have more information to display depending on the chosen options.
For this reason, we need ...
Inspection
1.
After disconnecting the vapor hose from the PCV valve, remove
the PCV valve.
2.
Reconnect the PCV valve to the vapor hose.
...
Copyright © www.kifomanual.com 2014-2025